看到的一个编制的皮革储物篮教程,感觉好看又实用,教程中有一张平面示范图,但研究了半天,也不知道该怎么编制,所以发一个帖子请教大家,谢谢!



为避免歧义,放上原文。



Materials

You’ll need: Leather, rivets, rotary knife, metal ruler, cutting mat or protective surface, needle-nose awl, small mallet, leather punch, rivet setter.



Materials

You’ll need: Leather, rivets, rotary knife, metal ruler, cutting mat or protective surface, needle-nose awl, small mallet, leather punch, rivet setter



Step 1: Choose and Cut Leather 

Pick leather that’s thick enough to feel sturdy but thin enough to cut; mine was 3 mm thick. Cut the leather into 1″-wide strips with a sharp rotary knife. For the basket, you’ll need four 20″-long pieces, three 40″-long pieces and two 26″-long pieces. For the handles, you’ll need two 14″-long pieces.





Step 2: Lay Out Basket and Punch Guide Holes 

Lay out the strips on a cutting mat or protective surface to form the basket’s framework, as shown in the template (above). The basket
 is held together by a rivet at each point where the strips overlap. For each rivet, start by punching a guide hole at the centre of the overlap using the mat guidelines or a T-square, plus awl and mallet.



Step 3: Punch Rivet Holes and Attach Rivets

Next, punch a hole for each rivet using a sharp leather punch centred on the guide hole, and attach the rivet using a rivet setter and mallet. (See my tips below on forming the basket.) Choose rivets long enough to fit through two thicknesses of leather.
 I used 7-mm rivets in a nice brass finish that add a metallic touch against the soft leather.

Tip: As you rivet, start by keeping the strips flat, as shown in the template, and attaching the 40″ and 26″ pieces to the 20″ pieces. Then, rivet the two ends of each 40″ piece so they form three bands. (These will be the basket’s sides.) Fold the 20″ pieces over and rivet to the outside of the bands. (At this point, you should have two longer sides and the base of the basket.) Finish by folding up the 26″ pieces and attaching to the bands to form the two shorter sides.




Step 4: Attach Handles 

When the basket is formed, attach the two 14″-long pieces as handles by riveting them to the 26″ pieces. The rivets won’t go through three layers of leather, so be sure to attach at a point with only two layers. Fill with books or toys, and enjoy!



  • {{ comment.commentator.username
    同等答案
    2015-11-25 22:08
  • {{ comment.commentator.username
    我不懂皮革哈……但是看那个图,下面的三个长横线应该是围一圈成为篮子的四周;那个圈圈是作为篮子的底;两侧的把手是按照step 4 后加上的。仅是猜测哈
    2015-11-26 09:00
  • {{ comment.commentator.username
    呵呵,只可意会,不可言传。
    2015-11-26 11:05
  • {{ comment.commentator.username
    中间部分是底部吧,长边是四周。
    2015-11-26 12:01
  • {{ comment.commentator.username
    a dog
    2015-11-30 11:46
  • {{ comment.commentator.username
    @月如刀 晕倒
    2015-12-04 21:24
  • 阿辛

行动
  • 转载2
  • 加入清单
  • 分享到

手工客帐号登录

手工艺人和设计师的兴趣分享社区

iOS、Android 均可扫码下载 APP